- #3080 POWER CONSUMPTION DRIVERS#
- #3080 POWER CONSUMPTION SOFTWARE#
- #3080 POWER CONSUMPTION PC#
Aug 16th, 2022 Corsair Dominator Platinum RGB DDR5-6600 C元2 2x 16 GB Review. Aug 19th, 2022 Gigabyte X570S AERO G Review. 
Aug 15th, 2022 Marvel's Spider-Man Remastered: DLAA vs. #3080 POWER CONSUMPTION PC#
A symptom of this is when your PC suddenly turns off when a game is starting, or during gameplay. It provides additional insight into power supply requirements because large spikes can trigger various protections on some cheaper power supplies.
Spikes: During all previous tests, we recorded the power draw and found the highest single reading, which is reported in this "Power Spikes" test. It averaged 384W in both FurMark and Metro Exodus, about 25W more than. For graphics card that can't reach 60 FPS at 1080p, we report the power draw at the highest achievable frame rate. It's not the most power-hungry graphics card we've ever tested, but the MSI 3080 12GB Suprim X can draw quite a bit of power. This test is also useful in testing a graphic card's ability to react to situations with only low power requirements. In this test, we run Cyberpunk 2077 at 1920x1080, capped to 60 FPS. V-Sync: If you don't need the highest framerate and want to conserve power, running at 60 FPS is a good option. Our high-speed test equipment is able to capture power spikes that occur very quickly, before the power limiter on the graphics card can react. All modern graphics cards have power limits, which are tested in this scenario. Maximum: We use Furmark's Stability Test at 1920x1080, which results in very high no-game power consumption that can typically only be reached with stress-testing applications. We ensure the card is heated up properly, which ensures a steady-state result instead of short-term numbers that won't hold up in long-term usage. Gaming: Cyberpunk 2077 is running at 2560x1440 with Ultra settings and ray tracing disabled. This codec has GPU-accelerated decoding on every modern GPU, so it not only tests GPU power management, but also efficiency of the video decoding hardware. Video Playback: We use VLC Media Player to watch a 4K 30 FPS video that's encoded with H.264 AVC at 64 Mbps bitrate, making it similar enough to many streaming services without adding a dependency on internet bandwidth. When using high refresh rate monitors, power consumption can be higher than in this test. When using two identical monitors with the same timings and resolution, power consumption can be lower. The card is left to warm up in idle mode until power draw is stable. #3080 POWER CONSUMPTION DRIVERS#
Windows 10 is sitting at the desktop with all windows closed and drivers installed.
The refresh rate is set to 60 Hz for both screens. One monitor runs 2560x1440 over DisplayPort, and the other monitor runs 1920x1080 over HDMI. Multi-monitor: Two monitors are connected to the tested card, and both use different display timings.
Idle: Windows 10 sitting at the desktop (2560x1440) with all windows closed and drivers installed. #3080 POWER CONSUMPTION SOFTWARE#
We conduct a physical measurement using professional lab equipment, the values are not software sensor readings, which are much less accurate. Everything is measured on the DC side, it's not the power consumption of the whole system. All graphics cards are tested in their out of the box state (auto).All power consumption numbers reported on this page are "card only" values measured via the PCI-Express power connector(s) and PCI-Express bus slot. During the temperature recording above, while in Unigine SuperPosition gamemode we monitored the audio and the results are found below. For the load tests we set Unigine SuperPosition running in game mode continuously for ~30 minutes and recorded the peak/maximum GPU temperature.ĪCOUSTICSFor the purpose of testing audio levels we have the NDI KC-3300 sound level meter. Once the benchmarks were complete we left the card to reach a cooling plateau where we then took the idle temperatures. TEMPERATURETo test temperatures we measured idle temperatures after booting windows, letting all applications finish loading and ran a few benchmarks. Idle readings were taken 5 minutes after system boot to ensure any background services and applications had loaded. The CPU was always in a fixed state so did not affect the additional power load when the GPU was placed under 100% load using AIDA64 stability test (GPU Only) which was ran for 20 minutes at which point a load reading was taken. It is important to note that the figures below represent total system power use and not just the GPU. To test for power consumption, we take a measurement from the plug socket.
0 kommentar(er)
